Never pay down a deposit in a bank account until you have met the seller, seen signed a purchase agreement.
No serious private advertisers ask for a down payment before you meet.
Receiving an email with an in-scanned ID does not mean that you have identified the sender. You do this on the spot, when you sign a purchase agreement.
This S14B23 inline-four was removed from my 1989 BMW M3 and commissioned a rebuild that included boring the block to 94mm and painting the inside of the block with Glyptal. A replacement crankshaft was ground 0.010? before being installed together with new bearings, forged IE H-beam rods, Carrillo pistons, ARP hardware, and a baffled oil pan. The cylinder he...
8.000 $
2 months agoEngines & GearboxesUsedSell20 people viewed
This DG400HD was removed from a BMW M3 Race car and is in good working order. This high performance gearbox is perfectly suited for use in front engine, rear wheel drive cars with medium capacity (turbo) engines. Its reliable design has been used in several motorsport categories and can handle up to 500 Nm of torque. A variety of standard applications are av...
4.200 €
3 months agoEngines & GearboxesUsedSell48 people viewed
Beckert Technology 6 Speed FWD sequential gearbox with Renault bell hosing. 6 speed and reverse, straight cut with dog engagement, hydraulic clutch bearing, and plate LSD.
For sale 0 miles/dyno time only Richardson 3.5 DFR top spec engine complete with injection loom and programmed ECU, with special flight case. Complete with ignition and injection systems ready for installation.
48.000 €
6 months agoEngines & GearboxesUsedSell91 people viewed
This is a nicely used BMW M3 E30 S14 Engine we have for sale. BMW S14 Race engine steel crank with 90 mm stroke steel rods forged pistons big valves, motorsport camshafts comes complete with intercooler and pipes and alu radiator and has full motorsport loom (no ecu)
7.000 €
6 months agoEngines & GearboxesUsedSell60 people viewed
Direct bolt in for any vehicle equipped with T-56 or T-6060. Features ground gear sets, precision dog clutch shifting, filtered circulating system, flat shift option. Newly rebuilt. FIA GT3 homologated transmission, EMCO DV46. Ready to install, complete with shifter / strain gauge
13.500 €
6 months agoEngines & GearboxesUsedSell59 people viewed
BMW S14 B23 Engine for sale,Completely rebuilt less than 2,000Km, Bore x stroke 93.4 x 84.0,forged steel crankshaft with 5 main bearings 55mm diameter, big end journals diameter 48mm, 2 overhead camshafts (DOHC) chain driven.
11.000 $
9 months agoEngines & GearboxesUsedSell69 people viewed
This Ford-Cosworth BDG 2.0-liter inline-four was acquired eight years ago and was rebuilt by Savannah Race Engineering in 2014. Work included machining the block and installing new pistons and bearings. The engine has not yet been installed in a car, though a dynamometer test showed an output of 276 horsepower and 188 lb-ft of torque. Planned to use the engi...
Vds gearbox sequential 3MO clio 3 rs 300km time trial Exit from 3MO for self-assembly block quad disc), control and reassembly by them. Alcon hydraulic thrust bearing Box exit trainer with new bellows (complete transmission possible depending on assembly. New long hub helix clutch disc Pendulum box support Unlocking cable + potentiometer.
Gearbox BE Citroën C2 Challenge 13x68 complete set For sale BE box of C2 Challenge, out of revision. Complete set, as pictured, ready to fit in a C2 (all genuine Citroën Sport parts): - box - universal joints (1.5 sets because one is twisted and therefore only for parts) - linkage - cradle - complete clutch with Alcon disc - lightened flywheel More photos av...
Sell box Sadev ST75/14 revised + clutch Sachs 4 damped pads + Dashboard AIM MXL Strada The gearbox is equipped with a Renault Sport spacer ref. 77 11 155 475 can therefore be mounted on C1J, F7P, F7R, K4M, F4R etc... It is equipped with a torque 13/54. The clutch shaft as well as the gears are almost new (4 slaloms and 2 regional rallies), The bearings are...
